How To Fix Broken Posts On Chain Linked Fense

Depending on the type of post and how information technology was ready in the ground, replacing a fence post can exist a manageable job. Taking into account what fabric the post is made of will assistance you lot go the job done well.

1
Examine the post.
- Subcontract fencing ordinarily only has the corner poles set in cement while suburban wood fences may have every woods postal service set in cement.
- Tubular metallic posts such as those used with concatenation link fence, are more often than not fix in cement.
two

Remove the fence from the post by removing screws or nails and pulling it away from the post as much as possible. ^[ane]
3

Elevator the postal service away if it is loose or broken at the bottom. ^[ii] If information technology is firmly set, proceed to the side by side pace.
4

Cut the postal service off just below ground level with a jigsaw, or hacksaw if leaving the cloak-and-dagger portion is not a problem with future plans. If leaving the bottom of the post in the basis is a problem, do not cut off the mail, keep to the next step.
5
Determine if the mail service was fix in cement.
- Dig around the mail service to await for cement.
- Use a probe close to the post to feel for cement.
6
Remove the sometime post. ^[three]
- If information technology'southward not set in cement push button the post dorsum and along in the hole until information technology loosens, then lift it up. If it is stubborn you may need to dig around the postal service on all sides until the post loosens.
- A postal service anchored in cement will demand to exist pulled out. Cutting a notch about the top of the post. Adhere a heavy duty chain or cable nether the notch. Attach the other stop of the chain or cable to a tractor or truck and pull it out.
7

Cull a new post that is the same shape and height of the former post.
8
Dig the new pigsty if yous cutting off the postal service. ^[4] A post hole digger or a narrow spade works all-time.
- Dig as close to the old hole as possible, exactly even with it.
- Make the hole almost 6 inches wider than the postal service on all sides.
- To determine depth measure out the old mail service from the superlative to where information technology set in the soil. Decrease that from the length of the new post. The answer is the depth y'all need for the new hole.
- Hire a powered auger that can make holes for debate posts if you lot take a lot of posts to replace.
9

Clean out the erstwhile hole of gravel, broken cement or loose soil if y'all are re-using the hole you removed the mail from. Brand sure the depth is correct by measuring as you would for a new hole.
x

Set the new post in the pigsty. Place a small level on acme and adapt the post until it sits level in the hole. Have someone hold the post level or use props to hold it in place.
11
Fill in around the post.
- Mix a bag of ready mix cement co-ordinate to package directions. Pour it effectually the mail service to the elevation of the hole. Let it dry out 24 hours.
- If you don't use cement, and are replacing a wooden post put pocket-sized gravel in the lesser 6, inches,(15.2 cm), of the hole, then make full the pigsty with soil to the pinnacle and pack it downwardly firmly. Metal poles do not need gravel.
12

Re-attach the contend to the mail service.

1

Remove any fence fastened to the post. ^[5]
2

Drive the broken post below ground level with a sledgehammer if a metallic postal service is broken off virtually the footing.
3
Remove the former mail if the post is badly bent or cleaved off well above ground. ^[half-dozen]
- Push the post or postal service piece dorsum and along, rocking information technology vigorously to loosen the pole.
- Pull straight upwards on the post to elevator it from the ground. This method works well for those with a strong grip and with a few poles.
- Rent or buy a post puller if the ground is very difficult or there are many posts to pull. Yous may have to straighten bent posts for information technology to work. A post puller works using a jack-like device to lift the post out of the ground. Some can be powered by hand and others by a power accept off drive shaft on a tractor. If you are pulling hundreds of posts y'all'll desire to rent a powered post puller.
4

Select a new post the same length as the old mail service.
5

Identify the new mail shut to where y'all removed the old one and as close to the fence as possible.
6
Drive the new mail into the basis until the triangular bract at the bottom is beneath ground.
- Use a post driver, which is a hollow tube with a weighted finish that fits over a metal fence post. It has handles on both sides. You lift the driver and allow it fall on the postal service to drive in the post. They are inexpensive and you can find them at subcontract stores or hardware stores.
- Use a sledgehammer if you don't take a mail service commuter to drive the post in.
7

Re-attach the contend to the post.

Add New Question

Question

Can I remove a wooden post and supercede it in the same concrete pigsty?

Juan Perez

Community Answer

Remove the old concrete and keep the new mail service level until the new concrete is set. Make sure the new hole is a petty wider than the new post.

Ask a Question

200 characters left

Include your electronic mail accost to go a message when this question is answered.

Submit

Video

A modest car or backyard tractor may non have enough power to pull out posts anchored in cement.
If yous are well-nigh a water source, a potent jet of h2o aimed at the post base can help loosen the soil.
You lot may need to loosen the contend at the posts on either side of the post yous are replacing to requite yourself space to work.

Show More Tips

Use safety goggles when cut off poles.
When pulling out posts with a chain and tractor or truck, make sure anybody is far from the surface area in case a chain snaps or a pole goes flying. Pull slowly steadily and don't make fast jerky pulls.
Don't leave jagged post edges sticking above ground. Make a second cutting below footing level, sand it off, or hammer down edges.

Things Y'all'll Need

Pliers
Wire cutters
Hammer
Nails
Screws
Wire fence clips
Safety goggles
Work gloves
Saw - hand saw, hacksaw or jigsaw depending on what you demand to cutting.
Heavy duty pulling chain - x feet (3.0 thousand) or longer for pulling posts in cement
Fence mail service puller if pulling many driven in posts
Mail service driver or sledgehammer for driven in metal posts
Shovel, spade or posthole digger
Ready mix cement (for anchoring some posts)
Gravel - for wood posts if non using cement
Level
Measuring tape
Some woods props for holding posts straight if you don't accept a helper